Well operation is impossible without the use of the obligatory component of its arrangement - a pump. After all, a bucket is absolutely not suitable for taking water from a narrow trunk. In addition, lifting up from the depths and transporting water manually would take too much time and energy. I don’t want to waste either one or the other, do you agree?
Properly selected pumping equipment in a matter of minutes will fill the tanks in the bathhouse, house, garden. Now there is an opportunity to purchase equipment for servicing an object of any scale. On its base, you can easily build an automatic water supply system that does not depend on centralized supplies and the participation of owners in the pumping process.
We will tell you in great detail how to choose a pump for the well, what you need to consider and provide for the future owner of the device. A thorough explanation of important points for the user is supplemented by photos and video guides.
Well Characterization
Before acquiring a suitable pump for a well, it is necessary to clarify a number of indicators of its structure:
- static level;
- dynamic level;
- flow rate;
- bottom bottom mark;
- pipe diameter.
If a specialized drilling company was engaged in drilling the well, then in accordance with the contract the owner had to provide its technical passport. All the characteristics mentioned above must be indicated therein. However, in cases where the well has been used (or not used) for a long time, it will not hurt to clarify this information.
Owners of wells that were created on their own or with the help of hired “co-workers”, of course, do not have such a document. They have to study their well on their own and establish its characteristics using simple measurements.
The static level is the distance that separates the constant mirror of water and the surface of the earth. To set this distance, you need a twine with a weight attached to it in the form of a cylinder or cone without a bottom.
Instead, you can use a plastic tube. You will also need a tape measure or ruler. The length of the string should be comparable with the depth of the well.
To measure the depth of the well, its dynamic and statistical level, you need to use a coil of rope or twine with a load at the end
Before starting measurements, you must refrain from taking water from the well for at least an hour. During this time, the water level should become maximum. Now the twine with the load is lowered into the well until the load “slams” on the surface of the water. The characteristic sound is usually clearly audible.
It remains to make a mark on the twine, remove it from the shaft and measure with a suitable tool. The first indicator of the well characteristics is determined. The dynamic level is the distance from the surface of the earth to the minimum water level in the well shaft.
To determine the dynamic level, the well must first be prepared. Water is pumped out with a high-performance submersible pump (it can be bought or borrowed), lowering it down as the water decreases.
The static water level indicates its maximum amount in the well, and the dynamic level indicates the minimum amount of water when the pump is running
When the water stops falling, we can assume that the minimum water level in the mine is reached. Now you need to do operations with twine, cargo and tape measure again. Measurements will give a new indicator of the well - its dynamic level.
Comparison of these data - static and dynamic levels - allows you to make a preliminary conclusion about the productivity of the well. The smaller the difference between these indicators, the faster the water column is filled, and the more powerful the pump can be used with such a structure.
It is worth noting that for a good artesian well, the dynamic and static level indicators may well coincide, which indicates the extremely high productivity of such a structure. This happens because water arrives as fast as it is pumped out.
The difference in levels for a high-productivity well usually does not exceed one meter. Dynamic level information is useful when installing a submersible pump selected for the well. Its immersion depth should be two meters above the dynamic level so that the device is always in the water.
The flow rate of a well is the amount of water that can be obtained from it within a unit of time. It is measured in the following units: l / min, cu. m / h, cubic m / day, etc. If the water level changes insignificantly when pumping water with a high-power pump, then the water arrives quickly.
To determine the flow rate of a well, it is necessary to pump out water from it, measure its volume, and also find out how long the well will be filled with water again
We can assume that the flow rate of a well is large and choose a pump with high productivity for it. When calculating the flow rate of a well, it should be remembered that this is not a constant value. In the spring, water arrives at the well faster than in summer, and in winter this process is slower.
To understand that the well was filled with water and the flow stopped, you just need to measure the depth of the water level. If it coincided with the previously obtained static level, then the well is filled. Those. after pumping water, such measurements will have to be performed several times.
The static level is measured before pumping out or after full recovery of the hot water mirror after pumping. Dynamic level is measured immediately after pumpdown
If the water quickly decreases and arrives slowly, it will be necessary to establish the exact volumes of water that can be obtained from this well. It is necessary to take the capacity of a significant and at the same time known volume. Most often they use a barrel, but it can be some kind of tank, bathtub, etc. The main thing is to know the volume of liquid that is placed in this container.
First you need to lower the pump closer to the bottom of the well and completely pump water out of it. This will be reported by the characteristic “sobbing” sound of a running pump.
Then time is noted and they wait until the static level in the well is restored. After that, the water is again pumped out, measuring its volume. By simply dividing cubic meters by hours or liters by minutes, you can determine the debit of your well.
This indicator will allow you to choose a pump, the performance of which will correspond to the volume of water arriving in the well. If the equipment is too powerful, the well will be empty, which may cause the pump to run dry, i.e. without water. And this leads to rapid damage to equipment.
The diameter of the submersible pump must be at least 3 cm smaller than the inner diameter of the casing. This is necessary to prevent jamming of the unit in the output
To determine the mark of the bottom of the well, i.e. its depths, again use twine with a weighty load without cavities inside. Now it is lowered to the bottom, until the twine weakened. After that, it is removed and measured.
Usually only the wet part of the twine is measured. Its dry part corresponds to the statistical water level in the well. The total depth of the well is equal to the sum of two values: the static level and the depth to the water mirror.
The diameter of the well is the diameter of its casing.To select a submersible pump, the internal diameter should be taken into account, since the dimensions of the pump should allow it to be freely lowered down, and if necessary, removed again.
Analysis of small nuances
The quality of drilling is another point to consider when choosing a pump for a well. If the drilling was carried out with the help of professional equipment and by a specialized team, such a well is considered more reliable.
If the drilling was done by co-workers or the owners of the site with the help of amateur friends, the quality of the well will hardly be ideal.
If the well is drilled professionally, it will be less likely to silt and sand, which will favorably affect the operation of pumping equipment
"Amateur" wells, as practice has shown, are more susceptible to the processes of flooding and sanding. Therefore, for such wells, it is recommended to use special pumps designed to operate in difficult conditions. Equipment of this type is more expensive.
But it better tolerates situations when they receive water with a lot of pollution. Under the same loads, conventional pumps break more frequently. Owners of “professional” wells have more options when choosing equipment, since they can choose both a universal and a special pump.
It is not always convenient to use a rubber hose to lift water from the depth of the well to a height. During the operation of the pumping equipment, air inside the hose becomes rare, from this the walls of the hose collapse, and the flow of water stops. To prevent this phenomenon is simple: instead of a rubber hose, plastic constructions of suitable diameter should be used.
A pressure-based water supply pipe is more effective when used in a well than a rubber hose that can collapse, blocking the water supply
An important indicator when choosing a pump is the approximate water consumption for one day. This is an average value, since in summer the water consumption usually increases, and in winter, on the contrary, it decreases. It is believed that the daily intake rate for a family of three to four people is approximately 60-70 liters.
These figures do not take into account water consumption for irrigation and other household needs. The daily rate should be increased depending on the number of plants on the site, the presence of pets, etc.
Prudent owners often choose four-inch casing pipes for the well, although designs with a diameter of three inches are also used as such. The fact is that a significant part of the pumping equipment is designed specifically for a more spacious four-inch pipe.
To convert centimeters to inches, you should divide the measurement result with a tape measure by 2.54, since this is exactly the number of centimeters that is equal to one inch.
In order to ensure sufficient pressure for operation at all points of the draw-off, a hydraulic calculation is necessary. An approximate version of this can be done using this table. All points must be provided with a pump sufficiently.
Differences between surface and immersion units
All domestic pumps at the installation site are divided into two types: submersible and surface. The first is lowered down almost to the bottom of the well. The second work on the surface. They are usually installed next to a water source or directly on the surface of the water using a special float.
Surface models use the principle of suction. The efficiency of such a pump is significantly affected by the distance that water has to be lifted. Usually they are used only if the depth to the water mirror is eight meters or less.
Surface pumps are successfully used, but only for wells of shallow depth, since these devices cannot cope with the rise of water to a height of more than 8 meters
If we are talking about the Abyssinian well, of course, the surface pump will be just the perfect choice, since we are talking about a very specific well - narrow and shallow.
But when operating a filtration or artesian well, a surface pump may simply not be able to cope with the load. In this case, it is necessary to choose a submersible model.
When choosing between a submersible pump and a surface pump, a much higher noise level should be taken into account when the latter operates. To eliminate this trouble, just close the pump with a wooden box or install it in a separate room.
Image Gallery
Photo from
The essence of the design of the Abyssinian well
Abyssinian well pump
Needle well pumping station
Abyssinian well manual pump
If surface pumps draw in water, then submersible pumps push it up. When choosing such a pump, the height at which water will have to be supplied, or rather, the distance from the surface to the pump, is primarily taken into account.
Therefore, a couple more meters should be added to the data on the dynamic water level. The boundary is considered to be a height of 40 meters. If the data exceeds this figure, you will have to pick up a high-power pump. The technical passport of each product indicates the maximum height to which it can supply water.
So that the noise from the surface pump does not interfere with others, as well as to protect it, the device is placed in a special box, which you can buy or make yourself
Visually, pumping equipment of high and low power varies significantly. More productive submersible pumps have a large body and weigh significantly more models that cope with immersion depths of up to 40 meters.
Focusing on the depth of immersion, it is better to give preference to units with a certain margin of performance. If the pump is designed to operate at a depth of 60 meters, it is more suitable for a 50-meter well.
For a deep well, you should choose a submersible pump, since surface models are not designed to pump water from a depth of more than 10 m
If it is lowered to the maximum depth, the unit will have to constantly work at maximum load, which will increase its wear rate and shorten its useful life. For a well with an immersion depth of 60 meters, it is better to take a pump designed for operation at a depth of 70 meters. The presence of automatic protection against “dry running” is an important point when choosing a pump.
For various reasons, water may stop flowing into the device. If at the same time the pump continues to work, it may overheat, break, burn out, etc. If there is appropriate automation, the device will be disconnected from the power supply as soon as it starts to idle, which will prevent malfunctions.
Image Gallery
Photo from
Submersible Pump Models
Submersible pump connection
Pump Installation
Caisson for a well with a submersible pump
The specifics of submersible pumping equipment
By the type of device, centrifugal and vibration pumps are distinguished. First, a rotating disk with blades is used to supply water, and secondly, a special membrane that transmits water through numerous vibrations. These design features are important because they affect well integrity in different ways.
Vibration pump + well: yes or no?
Can a vibration pump be installed in the well? These models are relatively inexpensive, easy to operate and have a productivity that is suitable for a significant number of wells.
Many experts strongly object to the use of any vibration technology in the well shaft. However, owner reviews indicate that this type of pump is used quite successfully without any damage to the structure. So which pump - vibrating or centrifugal - is better for a well?
The objections of the experts are well-founded. Prolonged vibration exposure almost always negatively affects the state of surrounding objects. A well is no exception.
Image Gallery
Photo from
Inexpensive domestic vibration pump
The most famous representative - Baby
Easy installation in the well
Easy repair and spare parts availability
Nuances of repair of vibration pumps
Filters for vibrating pumps
Vibration Pumps
Vibrations from a pump located next to the filter affect the condition of the casing and surrounding soil, which are gradually destroyed. Vibration can cause a significant acceleration in the processes of siltation and sanding.
But this does not happen right away. Typically, wells successfully resist vibration for some time. Therefore, with the help of such a pump it is possible to swing the well, and clean it, and successfully operate without visible damage.
But destruction by vibration does occur, although not too quickly. Continuous use of the vibration pump can significantly reduce the life of the structure.
If necessary, the use of vibrational models is quite acceptable, but only as a temporary option. But at the first opportunity, you should replace such a pump with a safer centrifugal device.
Centrifugal Pump Selection Guide
To do this, you must carefully study the technical data sheet of the centrifugal device and find out several important points:
- what is the performance of the pump;
- whether its dimensions are suitable for the well;
- how deep can he raise water;
- what are the features of its installation and operation;
- how and on what conditions warranty service, etc.
Usually consultants give quite professional recommendations when choosing such equipment. It should be remembered that many manufacturers indicate the limiting rather than average characteristics for pumps, so you need to take into account a certain margin of service life.
Directly in the marking of a domestic pump or in a technical passport of a foreign country, two numbers important for selection are indicated. The first (in example 55) is the flow rate in l / min, the second (75) is the maximum head in meters
A few words about popular models
If a decision is made to use a vibration pump, most likely a “Kid” or “Brook” will be purchased. These models are distinguished by good performance, resistance to breakdowns and quite affordable price.
They are easy to clean or repair with your own hands. But for continuous use, the vibration technique is not suitable, it must be replaced as soon as possible.
The vibration pump “Baby” is a popular, but not too suitable choice for the well, since the vibration of the device can cause its destruction
Among the popular brands of submersible centrifugal pumps, it is worth noting “Aquarius” and “Vodomet”. They are very similar, but according to user reviews, Aquarius significantly wins in quality and durability, although it costs more.
However, the "Water Jet" has its followers. If you are lucky to get a well-assembled model, he will demonstrate quite decent results.
Submersible centrifugal pumps of the brand “Aquarius” have established themselves as reliable and durable equipment for the well, able to cope with increased loads
Special borehole pumps will cost a substantial amount, but such costs over time fully justify themselves.As an example of such a technique, it is worth noting the 3STM2 and 4STM2 models manufactured by TAIFU.
Clip # 2. Studying the recommendations of well construction specialists before choosing a submersible pump:
Clip # 3. An example of calculations when selecting an Aquarius submersible pump for water intake:
So, in order to choose a suitable pump, it is necessary to accurately study the characteristics of a particular well. You should also take into account the general need of the family for clean water and deal with the features of the functioning of various types of equipment.
Do you want to talk about how you yourself chose a submersible pump for a well? Would you like to share information useful for us and site visitors, have found flaws in the text? Leave comments in the block under the text of the article.